|
|
Post by enemyoffun on May 30, 2010 23:44:07 GMT -9
I downloaded your Fantasy Adventures minis from DriveThruRPG and was directed to your downloads page to retrieve the bases.
When I went to your downloads page and clicked on Bases, I got an error page that said no such page exists.
Can you investigate the problem and fix the page, if possible?
Thanks!
|
|
|
|
Post by squirmydad on May 31, 2010 10:46:39 GMT -9
Reloading the bases page from a backup, it should be back to normal by the time you check again.
JIM
|
|
|
|
Post by BilliamBabble Inked Adventures on Aug 7, 2010 16:24:21 GMT -9
I think I had the same problem - I downloaded a set of your ace kobolds, but I needed some bases. I will try again.  |
|
|
|
Post by Sirrob01 on Aug 7, 2010 18:07:31 GMT -9
|
|
|
|
Post by BilliamBabble Inked Adventures on Aug 8, 2010 13:47:11 GMT -9
Thanks! |
|
|
|
Post by Canuck Chuck on Jul 16, 2011 13:19:43 GMT -9
why do some of the WorldWorks games bases work and some don't?
I need Chunky Floors, very badly. thanks very much if it gets fixed!
|
|
|
|
Post by nikloveland on Jul 17, 2011 4:41:49 GMT -9
The cave and chunky floor should be working now.
|
|
|
|
Post by Canuck Chuck on Jul 17, 2011 14:23:58 GMT -9
The cave and chunky floor should be working now. thanks a bunch, dude! |
|
|
|
Post by afet on Jul 20, 2011 8:59:29 GMT -9
Are there blank templates available for the various base configurations? If possible I'd like them as PSD or CPT files with the layers intact, but I could manage with pdfs
I'd like to get some more textures done for Fat Dragon, but Tom's way too busy at the moment. I'll try to pull off grass and hardwood as quickly as possible.
Cheers,
Afet
|
|
|
|
Post by stevelortz on Jul 20, 2011 10:22:10 GMT -9
Hi, Afet!
I'm not very savvy at manipulating things digitally. When I want bases in a texture that isn 't already done up as bases, here's what I do: I find the largest piece I can of the texture I want on a tile, and print that out on cardstock. Then I run that piece of cardstock through the printer again, only this time, I print the One Monk blank template for the size and shape bases I want.
I am sure what you want to do will be much more helpful to the community as a whole than my simple jury-rig technique!
Have fun!
Steve
|
|
|
|
Post by afet on Jul 31, 2011 11:31:43 GMT -9
Hi, Afet! I'm not very savvy at manipulating things digitally. When I want bases in a texture that isn 't already done up as bases, here's what I do: I find the largest piece I can of the texture I want on a tile, and print that out on cardstock. Then I run that piece of cardstock through the printer again, only this time, I print the One Monk blank template for the size and shape bases I want. I am sure what you want to do will be much more helpful to the community as a whole than my simple jury-rig technique! Have fun! Steve Thanks Steve. I tend to just glue the texture to foamcore, then cut out little bases with slots. I was hoping to post some actual OneMonk bases with FDG texture. |
|
|
|
Post by stevelortz on Jul 31, 2011 19:11:43 GMT -9
Hi, Afet! I'm not very savvy at manipulating things digitally. When I want bases in a texture that isn 't already done up as bases, here's what I do: I find the largest piece I can of the texture I want on a tile, and print that out on cardstock. Then I run that piece of cardstock through the printer again, only this time, I print the One Monk blank template for the size and shape bases I want. I am sure what you want to do will be much more helpful to the community as a whole than my simple jury-rig technique! Have fun! Steve Thanks Steve. I tend to just glue the texture to foamcore, then cut out little bases with slots. I was hoping to post some actual OneMonk bases with FDG texture. That would be good, too! Especially since FDG tiles and models are so widely used. Have fun! Steve |
|
